Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
What're your ideas concerning How to Install a Bathtub?
Mounting a bath tub isn't precisely rocket science, but it does require strong plumbing, carpentry, and often, tiling skills. Replacing an old tub with a new one is also a reasonably tough project. If the old bathtub is readily accessible, the task can move quickly; if you need to open a wall surface to remove the old bathtub and place the new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will require a helper to vacate the old bathtub as well as set in the new one. See to it you have certified on your own for the work and also fit trying it. Rather than hiring a service provider to take control of a halfway-completed task, it is much better to think about employing one prior to you begin. Chances are you might need a professional plumber to make tube links.
This article will certainly assist you mount a new bath tub in your shower room if you have already gotten a brand-new bathtub and do not require to change the plan of your previous water supply pipes.
Your tools as well as product list need to comprise the following:
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bath should be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final position.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be quite bothersome because of the limited gain access to that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been eliminated, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Using both wooden boards under its feet, position the tub in the needed placement. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the tub until the spirit level reads level.
To mount faucets, fit all-time low of the furthest flexible faucet port to the proper supply pipe by making a compression sign up with; then do the same for the various other faucet.
Switch on the water supply and examine all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Load the bathtub and likewise examine the overflow outlet and also the normal outlet for leaks.
Ultimately, deal with the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub must wait till the bath tub has been used at least when as this will resolve it right into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin making certain that the washers are in location between the faucet as well as the sink. Secure the faucet in position with the maker offered backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to crack a rigid seal, creating the water to penetrate the wall surface in between the bath and the tiling, leading to complications with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the tub with water prior to sealing, to permit the activity experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that blog posting on Tools You Need to Install a New Bathtub when doing a search on the search engines. Do you know anybody else who is very much interested in How to Install a Bathtub? Do not hesitate to promote it. Thank you so much for taking the time to read it.
Rates Report this page